SI-Config --------- release notes 2.3.1 12.06.2012 Close COM port, if card read dialog is close 2.3.0 04.06.2012 removed unnecessary SI-Point settings a warning is shown when computer time should be set and the difference is larger than 2 hours SIAC bock 3: another identification Help-File: new links for sportident 2.2.8 18.04.2012 header file for SIAC configuration added 2.2.7 31.03.2012 implemented modified D3 command Config Card11, SIAC New Battery SIAC 2.2.6 12.01.2012 SI-Point no write 2.2.5 05.01.2012 ProductID = CFG0 all bits (SI-Point=49) 2.2.4 04.10.2011 country code as a CLI parameter possible Modes - BC D-Control und Instuction removed Mode - D-Posten becomes SIAC ReadOutRadio SIAC ReadOutRadio always with CN 127 bc Broadcast und bc Selective removed BattCons/Cap label bei BS10_11 still undecided 2.2.0 03.03.2011 SIAC: Read backup Switch to ClipBoard automatically Show D3 'Timing mode' from SIAC ScrollBar in main form for small screens 2.1.9 16.02.2011 SIAC direct control: show and select release notes 2.1.8 14.02.2011 implemented SIAC configuration BS11 settings (Beep, Led, Timing mode, Send by radio) SIAC additional values: clear, start, finish, Batt.-Date und -Volt, Hard- und Software 2.1.7 12.01.2011 SIMSRR Dongle settings Protocol new columns, new order Instruction 'Password' removed Batteries voltage registered in log file 2.1.3 07.09.2010 software no longer relevant for BS10_11, but for BS7, BS8 2.1.2 14.07.2010 software no longer relevant for BS10_11 operating time now equal to BS6 end address now equal to BS6 no message on capacity check 2.1.1 23.03.2010 CFG2 only USB or RS232 Dialog COM settings, if COM unavailably No restriction "Operating mode" and CN SIAC (SPORTidentActivCard) read backup (block 1, 4-7) "Extended protocol" only set with Standard view 2.0.9 02.12.2009 Read cards with new board and not "Extended protocol" 2.0.8 25.11.2009 bug fixes 2.0.7 06.11.2009 fixed CN limit to 767 Check current progam version and firmware version Help files as ..CHM files Set default values "Autosend" and "Extended protocol" with "Printout" mode Warning shown when BSM set up as "Control", "Finish", "Start" without "Autosend" flag 2.0.6 12.10.2009 "View punch" and "Read SI-Cards": "Find", "Find continue" 2.0.5 09.10.2009 "Read SI-Cards": save table before creating new one Current language: saved based no longer on index but on filename "New batteries" only in "Expert view" Program title with version 2.0.4 18.09.2009 "View punch": ignore NAK if BSF-SRR connected 2.0.3 14.09.2009 View next punch if 00:00:00 in Card 5 2.0.2 06.11.2008 minor bug fix for version 2.01 2.0.1 29.10.2008 serial port selection menue: plugged SPORTident stations pre-selected special handling for SI-WBOX-WLAN virtual COM-ports no operating mode selected after program start SPORTident USB-devices: battery consumptions counter values disabled 2.0.0 10.03.2008 new function: monitor window "view punch" for online stamps 1.5.0 27.11.2007 "Read SI-Cards" with show trigger punches "quick view" personal data at the end set no set on/off "Extended protocol", if "Standard view" this file show "help" - "Info SI-Config" - "Version 1.5.0 ...." warning: station software old version stations (besides control) with code no < 31 "Read SI cards" and "Printout" without cable and other stations with cable (besides start and finish) 1.4.9 22.11.2007 COM port: input, output with byte arrays 1.4.3.1 02.11.2007 (20.08.2007) new SI-ConfigSVE.XML language file battery change date: multi date-time format supported 1.4.3 11.04.2007 multi user support program settings (*.ini, *.log, *.bin) are not longer in program folder but in user tree support of "windows-like" user specific settings in folder tree (local application data folder of current user) program update period program release period is now one year language support additional language and help support (...HUN.XML, ...DAN.XML, ...FRA.XML, ...FRA.HLP) clear mode there is only one clear mode supported: clear completely 1.4.2 16.10.2006 minor bug fixes 1.4.1 14.10.2006 new "help"-files (enu,deu) language support modified for each language a separate XML-file is used; the file is fully editable by the customer; additional languages can be implemented by adding a new language file SI-Card readout easy data handover mechanism (to spreadsheet programs or other applications) a) option "DirectCards=" is set in SI-Config.INI: data file (*.csv) is written and stored after each SI-card read in or b) option "DirectCards=" is not set in SI-Config.INI: SI-Card data are copied to clipboard after reading tCard clear time is not shown if there are control stamps in the card set SI-station default values "BEEPLEN" standard value is set read backup data from printout station (BSP-7) "start punch in BSP-7": time stamp is shown in SI-card data, if there is no dedicated start punch in the SI-Card (mass start case) BSM-7 Expert-Mode baud rate COM/USB-Port can be fixed Programming BSF3...6 warning, if active time is < 04:00:00 h 1.4.0 14.03.2006 option: store card-readout data file each time a SI-Card is read out in SI-Config.INI add entry in section [FILES] DirectCards= 1.32 01.03.2006 minor bug fix for version 1.31 1.31 20.02.2006 help support, language support program update recommendation 1.30 13.01.2006 SI-Card6*: reading, soft setting switch for SI-Stations password service for SI instruction cards (lilac cards) SI-Card readout faster improved help (ToolTip) COM-port interface detection automatically SI station hardware detection automatically user interface: "standard view" and "expert view" 1.20 28.11.2005 new SI-Cards 8/9/p implemented password feature for SI stations